|
|
|
|
|
|
|
System Includes: |
|
18,000 BTU INVERTER Cooling Capacity: 9k x 2
18,800 BTU INVERTER Heat Pump: 9k x 2
16 SEER - R410A PreCharge - INVERTER DC
Install Kit (connection piping, drain, remote etc)
1 Year Part - 5 Year Compressor Warranty >>> |
|
|
|
|
|
|
|
|
|
|
Install Kit Contents: |
|
|
15 Feet Flared Insulated Copper Tubing x 2
15 Feet Pipe Insulation x 2 |
|
Drain Pipe (outdoor)
Wall Cross piping
Defrost Wire
Putty to seal piping / holes |
|
|
|
|
Remote Control w/ Wall Brackets & Batteries x 2
Wire Harness Between Indoor & Outdoor x 2 |
|
|
|
|
|
|
|
|
|
Inverter Technology: |
|
|
|
|
|
|
|
|
|
|
|
Install Kit Contents: |
- 15 Feet Flared Copper Tubing x 2
- 15 Feet Pipe Insulation x 2
- Drain Pipe (outdoor)
- Wall Cross piping
- Binding Belt - Catchment Trough
- Remote Control Wall Bracket x 2
- Wall Hole Block Putty & Insulated Tape
|
|
|
|
|
|
|
***Extend one or both of the two (2) included 15 foot line sets to a total length of 20 feet. Just $112 per 25' extension.*** |
|
|
|
BASIC OVERVIEW: The indoor unit is hung like a picture frame approximately 6 - 8 feet above the floor usually on an exterior wall. A 2-3 inch hole must be made behind the indoor unit in the exterior wall to run the refrigerant copper tubing, electrical wires and the condensate drain to the outside unit. The indoor unit and outdoor unit are connected to each other by means of refrigerant copper tubing and electrical cables. The condensing unit comes pre-charged with freon however, the lines still need to be vacuumed to evacuate the excess Nitrogen prior to the final coupling. *Although the installation may seem easy to some, certain tools and experience is necessary to complete setup of a mini split* See Installation Tip. A certified HVAC technician must conduct / complete the installation to be eligible for the warranty. See warranty details below > |
|
|
|
|
|
|
|
|
|
|
5 YEAR COMPRESSOR WARRANTY - 1 YEAR PARTS WARRANTY. Details: Unit must be installed by a licensed HVAC (Heating, ventilating, and air conditioning) company to be eligible for product Warranty. Damage resulting from failure to use, install or maintain the product in a manner consistent with our/manufacturer's recommendations shall render the warranty void. Thermospace.com, at its option, may request a report from a qualified technician prior to honoring a warranty claim. We shall not be responsible for faulty installation, operation or maintenance of the product. It is the responsibility of each purchaser to determine whether the particular product is compliant with and permissible for use pursuant to the applicable rules, codes and/or regulations. if any, and suitable for particular and/or intended use and/or operation therein. Once a non defective unit is installed by a HVAC company, chances of anything going wrong with such unit is very slim. But worst case scenario, if you come across any issues, consumer can call the company that installed the unit (usually they will cover this FREE as it falls under installation warranty). If it was determined that the unit is not functioning due to a defect and needs to be replaced, the part will be sent free of charge. If the compressor is defective, a BRAND NEW replacement will be shipped out. If the indoor unit is defective a BRAND NEW indoor unit will be sent out free of cost. (labor charges incurred will not be covered under this warranty) |
|
|
|
|
These mini split unit ships via FEDEX FREIGHT (on truck) and will be divided between 3 parcels per system (install kits - condenser - air handlers). These units ship out of South Florida, and under normal conditions, are in transit within 1 - 2 business days of payment receipt. Depending on where you are geographically located, transit time typically amounts to an additional 2 - 5 business days. Please provide a contact phone# upon checkout where recipient of order can be reached at. SOMEBODY MUST BE ON SITE TO ACCEPT SIGN FOR PARCEL(S). Only ships to the lower 48 Contiguous United States. |
|
|
|
|
|
Extension Kits
Extend Included 16' to 25' or 33'
Required Size: 1/4" x 3/8"
Price: $144.00 - $227.00
Click for more Info > |
Condensate Discharge Module
- Discharge Head Up To 50 Feet
- 120 & 220 VAC Models Available.
Price: $179.00
Click for more Info > |
Condenser Bracket
- Mount The Condenser At Any
Height On An Outdoor Wall.
Price: $59.00
Click for more Info > |
Micro-Pump II
- 3.2 Gallons per Hour Rate
- 120 & 220 VAC Models Available.
Price: $149.00
Click for more Info > |
|
|
|
|