|
|
|
|
|
|
Technical Data: |
|
57,500 BTU's of Cooling Capacity
58,000 BTU Heat Pump
10 Year Limited Parts Warranty View Details > R-410 Precharged - 13 SEER - 8.2 HSPF |
|
AC System Includes: |
|
Indoor Unit - Air Handler
Outdoor Unit - Condensor Product and Installation Manuals |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Air Handler - (indoor) technical: |
|
Airflow: |
1950 CFM |
Dimensions: |
22" W x 54 1/2" H x 24" D |
Weight: |
135 lbs. |
Power Supply: |
230/208 - 60Hz |
Circuit Amps: |
2.79 |
Minimum Circuit Ampacity: |
4 |
Maximum Circuit Protector: |
15(A) |
Noise Output: |
58 dB(A) |
Horse Power: |
3/4 |
Speeds: |
3 |
Supply Duct: |
19 1/2" |
Connection type: |
Sweat |
Pipe Size (liquid - gas): |
3/8" - 1 ⅛" |
|
|
|
|
|
|
|
Condensor (outdoor) technical: |
|
Cooling Capacity: |
57,000 BTU's |
SEER: |
13 |
Heating Capacity: |
58,000 BTU's |
HSPF: |
8.2 |
Dimensions: |
29 ⅛" W x 32 ⅛" H x 29 ⅛" D |
Weight: |
222 lbs. |
Compressor Brand |
Copeland |
Compressor Type: |
Scroll |
Refrigerant: |
prec - R410A |
Outside Noise Output: |
67 dB(A) |
Power Supply: |
230/208 - 60Hz |
Compressor Input Power: |
4860 Watts |
Rated Current (RLA): |
21.8 Amps |
Locked Rotor Amp (LRA): |
134 Amps |
Refrigerant Oil: |
740 ml |
Fan Motor Input: |
377 Watts |
Fan Motor Speed: |
1120 r/min |
Number of Coil Rows / Tubes: |
2 / 28 |
Tube pitch (a) x row pitch (b): |
21 x 13.37 mm |
Tube Outside dia/type: |
7mm / innergroove tube |
Fin Coil Dimensions: |
85 1/8" x 1" x 31 3/8 |
Connection Wire - Power: |
6 mm2 |
Connection Wire - Signal: |
.8 mm2 |
|
|
|
|
|
|
|
BASIC OVERVIEW: The CSM-ARAM central AC systems are split between an outdoor unit and indoor air handler and connected to each other by means of refrigerant copper tubing and electrical cables. The air handler is mounted inside and uses ducts to distribute cooled air to 1 or more areas. The condensing unit comes pre-charged with R410A Freon for a lineset up to 25 feet...(connection cables, pipeing and indoor thermostat are not included).
Most Purchases of central AC's are usually intended to replace an existing system that has either burned out or simply become outdated and cost effective. In these cases, all the plumbing, wiring and connection pipeing is usually already in place. All you need to do is double check service ports - gauges are compatible, swap out the old system, re-charge the lines and you're good to go. For a new construction, additional supplies (locally purchased) will be required to install a central AC.* Although the installation may seem easy to some, certain tools and experience is necessary to complete installation* See installation Manuals: Air handler installation - condenser installation. Please consult an HVAC technician and use the provided PDF downloads for reference before making a decison to purchase. |
|
|
|
|
The installation of HVAC systems includes electrical, gas, and refrigerant connections, is generally regulated by a multiple sets of laws, codes and guidelines, at the federal, state and local levels. Further, the failure to properly install HVAC equipment can raise personal safety and performance concerns. No warranty is offered for the products that were installed by unlicensed/unauthorized persons.* |
|
Air handler is compatible for either horizontal or vertical installation: |
|
|
|
|
|
|
Click to Download Warranty Details: A Central AC system must be installed by a licensed HVAC (Heating, ventilating, & air conditioning) company to ensure any issues encountered in the future are not due to improper installation / workmanship. Central AC systems, are not "plug-n-play" units that can be properly installed without certain tools any prior HVAC - electrical knowledge. Warranty service - troubleshooting is provided through the contractor / installer and will be upheld as long as policies within Warranty spreadsheet are observed. Once a non-defective unit is installed by a HVAC company, chances of anything going wrong are very slim and almost all contractors will guarantee there workmanship and provide future service free of charge (installation warranty). If it was determined that the unit is not functioning due to a defect and needs to be replaced, the part will be sent free of charge. If you receive a damaged or defective product, a replacement unit will be sent out Free of cost. Damaged/Defective product will be picked up and a brand new exchange will be shipped out. |
|
|
|
|
Delivery typically wirgin 7 business days from payment receipt. All of our units are bubble wrapped, palletized and shipped to your home or
business via trucking line. This ensures the safe arrival and handling of your goods. Shipping companies vary based on your location but FEDEX freight is out most common carrier. Your shipment will be insured with the freight company against any loss or damage without additional cost to you. Damage or
loss is rare but it can happen during transportation, please make sure you inspect your equipment before you sign for it.
Please do not accept any unit with significant dent and damage and write down any damages on the truckers bill of lading. Your phone number is required to schedule your delivery or the goods will not be shipped. |
|
|
|
|
|
|
|
|
Electric Strip Heater for ARAM Air Handling Units available in: 5KW, 8KW, 10KW, 15KW & 20KW
- HK heat kits have built-in over current protection, over heating protection, Circuit breaker, and nickel chromium heat elements.
- The smart elecWtronic control board located in the air handling units controls the heater most efficiently based on your thermostat settings.
|
|
|
|
|